Learning the Basics of Installing a Bathtub
Learning the Basics of Installing a Bathtub
Blog Article
The article which follows about How to Install a Bathtub Yourself is unquestionably informative. Read on and draw your own personal results.
Mounting a bath tub isn't exactly brain surgery, but it does need solid plumbing, carpentry, and also often, tiling abilities. Changing an old tub with a brand-new one is additionally a moderately hard task. If the old bathtub is conveniently easily accessible, the task can relocate easily; if you have to open up a wall surface to remove the old bathtub and position the brand-new bathtub, the job is a lot harder. In either situation, the task is within a home handyman's skills, although you will certainly need a helper to vacate the old bathtub and embeded in the brand-new one. Make sure you have certified yourself for the task and also fit attempting it. As opposed to hiring a specialist to take control of a halfway-completed job, it is much better to consider using one prior to you start. Possibilities are you may require a specialist plumber to make tube links.
This post will certainly assist you set up a new bathtub in your washroom if you have actually already purchased a new bathtub as well as don't require to transform the plan of your previous supply of water pipes.
Your devices as well as material list ought to consist of the following:
Getting ready for the Installment
First of all, the sustaining frame provided with the bath must be fitted (if called for) according to the producer's guidelines. Next, fit the taps or mixer to the bath tub. When suitable the tap block, it is very important to make sure that if the tap includes a plastic washing machine, it is fitted in between the bathroom and also the taps. On a plastic bath, it is additionally reasonable to fit a sustaining plate under the faucets device to stop stress on the tub.
Fit the flexible tap connectors to the bottom of the two faucets utilizing 2 nuts as well as olives (occasionally supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the electrical outlet with the hole in the bath. Make use of the nut provided by the supplier to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the flexible overflow pipeline to the overflow outlet. After that, screw the pipe to the overflow face which must be fitted inside the bath. Make sure you make use of every one of the provided washers.
Attach the trap to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Link all-time low of the overflow tube in a comparable manner.The bathroom ought to now be ready to be suited its last placement.
Removing Old Taps
If you need to replace old taps with new ones as a part of your installation, then the first thing you ought to do is separate the water. After doing so, activate the faucets to drain any type of water continuing to be in the system. The process of getting rid of the existing taps can be fairly troublesome due to the limited accessibility that is typically the situation.
Make use of a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that attaches the supply pipelines to the taps. Have a fabric prepared for the staying water that will come from the pipes. Once the supply pipes have actually been gotten rid of, make use of the very same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly require to stop the solitary taps from transforming during this process. Once the taps have been eliminated, the holes in the bath/basin will certainly need to be cleaned of any old securing substance.
Before proceeding to fit the brand-new faucets, compare the pipe links on the old faucets to the brand-new faucets. If the old faucets are longer than the new taps, then a shank adapter is needed for the new faucets to fit.
Installing the Bathtub
Using the two wood boards under its feet, position the tub in the needed position. The wood boards are handy in equally spreading the weight of the bathtub over the location of the boards rather than focusing all the weight onto 4 small factors.
The next objective is to make sure that the bathtub is leveled all round. This can be attained by inspecting the level as well as readjusting the feet on the bathtub till the spirit level checks out degree.
To install faucets, fit the bottom of the furthest adaptable tap port to the ideal supply pipe by making a compression sign up with; after that do the exact same for the various other tap.
Turn on the water system as well as check all joints and new pipework for leakages as well as tighten them if required. Load the bathtub as well as also inspect the overflow electrical outlet and the typical electrical outlet for leakages.
Finally, repair the bath paneling as defined in the producer's instruction manual. Tiling and also securing around the bathtub needs to wait up until the bath tub has been used a minimum of once as this will settle it right into its last placement.
Suitable New Taps
If the tails of the new taps are plastic, after that you will certainly need a plastic connector to stop damages to the thread. One end of the connector fits on the plastic tail of the faucet as well as the other end provides a link to the existent supply pipelines.
If you need to fit a monobloc, then you will certainly require lowering couplers, which links the 10mm pipeline of the monobloc to the typical 15mm supply pipe.
Next off, position the faucet in the placing opening in the bath/basin guaranteeing that the washing machines remain in place between the tap and the sink. Secure the tap in position with the maker supplied backnut. As soon as the faucet is safely in position, the supply pipes can be connected to the tails of the taps. The taps can either be connected by utilizing corrugated copper piping or with typical faucet adapters. The previous kind should be connected to the faucet ends initially, tightening up only by hand. The supply pipes can later be linked to the various other end. Tighten both ends with a spanner after both ends have been connected.
Tiling Around the Bathtub
In the area where the bathroom fulfills the ceramic tile, it is necessary to seal the joins with a silicone rubber caulking. This is very important as the installation can relocate sufficient to break a rigid seal, causing the water to penetrate the wall surface between the bath and the tiling, causing problems with dampness and also possible leakages to the ceiling below.
You can pick from a range of coloured sealers to blend in your components as well as installations. They are sold in tubes and cartridges, and also are capable of sealing voids approximately a width of 3mm (1/8 inch). If you have a larger space to fill up, you can fill it with spins of soaked paper or soft rope. Keep in mind to always fill the tub with water prior to sealing, to enable the motion experienced when the bathtub remains in use. The sealant can split fairly early if you do not take into consideration this activity before sealing.
Additionally, ceramic coving or quadrant tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are likewise conveniently available on the market. It is suggested to fit the ceramic tiles using waterproof or water-proof glue and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I was brought to that editorial on A Step-by-Step Guide to Installing a Bathtub through someone on our other blog. Those who enjoyed our blog posting plz don't forget to share it. Thank you for your time. Come back soon.
Explore Report this page